The ignition switch is the first step to get your electric scooter running. However, if the ignition switch is not working, starting the scooter can be a real hassle.
Several times, the electric scooter may not start due to a faulty ignition switch. In such cases, bypassing it is necessary to get the scooter running again.
In this article, we’ll share some quick and easy step by step guides on how to bypass ignition switch on electric scooter.
Let’s get started.
How To Bypass Ignition Switch On Electric Scooter
An ignition switch or button is used to start the motor of an electric scooter. No matter what type of electric scooter you have, if it isn’t starting due to a faulty ignition switch, then you can follow these steps to bypass it.
Here are the easy steps to bypass ignition switch on an electric scooter.
Step 1: Remove the Handlebar
The first step is to remove the handlebar from the electric scooter. This will allow you to access the switch and its wiring.
To remove the handlebar, you’ll need to unscrew all the screws holding it. Once you have unscrewed the screws, carefully remove the handlebar.
Step 2: Loose Clutch Cable
Now you need to loosen the clutch cable from the handlebar. This will help to give a temporary power connection to the electric scooter motor.
To do this, locate the clutch cable and then use a wire or flathead screwdriver to loosen it. Make sure not to loosen it too much, as this can cause the motor to spin without any control.
Note that the green wire is the positive end, and the black wire is the negative end of the clutch cable. So connect it accordingly.
Step 3: Disconnect the Battery
Before you make any connections, it is important to disconnect the battery from the electric scooter. This will prevent any shocks or short circuits.
To do this, locate the battery and then use a screwdriver to disconnect it. You’ll need to unscrew the bolts that hold it in place.
Step 4: Remove the Cover Plate
Now remove the cover plate from the electric scooter. The cover plate is a plastic piece that covers the ignition switch.
To remove it, locate the screws holding it in place and then use a screwdriver to unscrew them. Once you have unscrewed the screws, carefully remove the cover plate.
Make sure the battery is off while you do this.
Step 5: Unscrew The Ignition Switch
Now you need to unscrew the ignition switch from its place. To do this, you’ll need to locate the screws and then use a screwdriver to unscrew them.
Once all the screws are loosened, carefully remove the ignition switch from its place.
Step 6: Check The Wire And Ignition Switch
Now you need to check the wire and ignition switch for any signs of damage. If there is no visible damage, then move to the next step.
However, if you can clearly see any signs of damage on the wire or ignition switch, then you’ll need to replace it with a new one.
Step 7: Connect Wires To Ignition Switch
Now that the ignition switch is removed, you need to connect the wires. You’ll need to locate the positive (+) and negative (-) terminals on the ignition switch.
Once located, connect the positive wire to the positive terminal and the negative wire to the negative terminal.
Step 8: Test The Ignition Switch
Now turn on the battery and test the ignition switch. To do this, press down the switch and see if the motor starts or not.
If it does, then the ignition switch has been successfully bypassed. If not, then you’ll need to check the wiring and connections before trying again.
Step 9: Reattach Handlebar
Finally, you need to reattach the handlebar. To do this, locate the screws and then use a screwdriver to tighten them.
Once the screws are tightened, your electric scooter should be ready to use again.
You might also like reading how to charge electric scooter without charger.
Tips If Ignition Switch Still Not Working
If the issue is not with the ignition switch, it could be related to the electric scooter battery or other components.
If the issue is related to the battery, you can try charging it overnight and see if it starts working again.
If the issue is related to other components, you can try to find a replacement part or seek professional help.
Otherwise, the last option left is to get it serviced at an authorized service center.
You can also read can you ride an electric scooter on the sidewalk.
FAQs
Q. Is there a way to bypass an ignition switch?
Answer: Yes, you can bypass an ignition switch by removing it and connecting the wires to it.
Q. What is the ignition bypass wire?
Answer: The ignition bypass wire is a wire that is connected to the ignition switch and allows for temporary power connection to the electric scooter motor.
Q. How do you start a scooter ignition?
Answer: To start a scooter ignition, press down the switch and see if the motor starts or not. If it does, then it means the ignition switch has been successfully bypassed. If not, then you’ll need to check the wiring and connections.
Conclusion
By following these steps, you can easily bypass the ignition switch on your electric scooter. However, if you still experience any issues related to the ignition switch or any other part of the scooter, then you can seek out professional help.
These simple steps can help you to get your electric scooter running again in no time.
This is the ultimate guide for how to bypass ignition switch on electric scooter. I hope this article has been helpful to you in getting your scooter running again.